Fits: KAWASAKI VERSYS 1000 models

Protect the vulnerable ABS Sensors from rocks, road debris and tip over impacts with these slick stainless steel guards laser cut from 2mm stainless. 

• Kit includes front and rear guards
• Easy 5-minute install using the stock fasteners and common hand tools
• Available in natural silver stainless finish

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSEOUT SALE! 

Installation PDF 

SRC Designs Cargo Tail Rack for Yamaha Ténéré 700 2021-2024 Version 1 (V1) 

Made of strong 3mm aluminum alloy plate for an optimal balance of strength to weight. Lots of openings for strapping and bungee cords.  This rack also includes stainless steel support brackets and is rated for up to 22 lbs  (10 Kg) of gear. 

• Black powder coated aluminium
• Laser cut 3.25mm aluminium plate 
• Light but super strong - only 1.3kg 
• Fits to 4 x existing mounting points on rear of bike
• Supplied with 4 x stainless steel standoffs to replace existing OEM units 
• Includes all stainless steel mounting bolts & counter-sunk washers
• Flat section of the rack sits  approximately 10mm above passenger seat (standard OEM seat)
• Slotted all round to cater for plenty tie down points
• Pre drilled to fit SRC 3 litre plastic fuel tank
• Easy to drill holes to fit the Roto-Pax fuel/water containers in a position to suit you
• Quick & easy fitment
• Please note this rack will not fit with the rally seat 
• Fuel tanks & fuel tank mounting brackets as seen in some of the photos are not included in price (sold as separate parts) 

The top rack is good for small luggage set up and especially Kriega luggage, however if you need access to the battery or electrics whilst on a ride you need to remove the rack which can be a little annoying and secondly the rack fits over the passenger seat so no place for a passenger to sit. The top rack with side racks is good for riders that have soft luggage and side racks are slightly raised off the side with rubber stands-offs so they stop potential damage caused by luggage rubbing on the plastics. The new rear rack V2 with grab rails  (available here) is great as it allows access to air filter & electrics etc. without the need to remove the seat whilst out on a ride. The real benefit of V2 is using the grab rails to pick up the bike or lift the bike out of ruts & muddy holes etc...as T7 has nothing to hold onto at the rear of the bike. This V2 option allows for much larger luggage to be carried as racks sits further out off the back of the bike. On a side note, the V2 version can also act as rear crash bars as they stick slightly out from the side of bike. We've tested all options and this also comes from reliable customer feedback.

Fitment:

• Yamaha Ténéré 700 years 2020 - 2023*

• *Not compatible with optional rally seat

Installation instructions and video*

Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

 SRC Designs Cargo Tail Rack for Yamaha Ténéré 700

CLOSEOUT SALE! 

The top plate is made of strong 3mm aluminum alloy plate for an optimal balance of strength to weight. Lots of openings for strapping and bungee cords.  This rack also includes stainless steel support brackets and is rated for up to 22 lbs  (10 Kg) of gear. 

Comparing this V2 HD tube frame rack with our V1 center rack, the center top rack of the V1 is good for small luggage set up and especially Kriega luggage, however, if you need access to the battery or electrics whilst on a ride you need to remove the rack which can be a little annoying and secondly the V1 rack fits over the passenger seat so no place for a passenger to sit. The full version of the V1  top rack with side racks is good for riders that have soft luggage as the side racks are slightly raised off the side with rubber stands offs so they stop potential damage caused by luggage rubbing on the plastics.

This new rear rack (V2) with grab rails is great as it allows access to the air filter & electrics etc. without need to remove the seat whilst out on a ride. The real benefit of V2 is using the grab rails to pick up the bike or lift the bike out of ruts & muddy holes etc...as T7 has nothing to hold onto at rear of bike. This V2 option allows for much larger luggage to be carried as racks sits further out off the back of bike. On a side note, the V2 version can also act as rear crash bars as they stick slightly out from the side of bike. We've tested all options and this also comes from reliable customer feedback.

Pre-drilled for our 3L fuel can mount

Available in Satin Black powder coat

Fitment:

• Yamaha Ténéré 700 years 2020 - 2024*
• • Black powder-coated 3.25mm aluminium top plate
    
  • 25mm (1") Chro-moly steel tube frame for increased load capacity and weight distribution.  Plus acts as much much-needed grab handle!
  • Fits to 4 x existing mounting points on rear of bike
  • Supplied with 4 x stainless steel standoffs to replace existing OEM units 
  • Includes all stainless steel mounting bolts & counter-sunk washers
  • Flat section of the rack sits  approximately 10mm above the passenger seat (standard OEM seat)
  • Slotted all around to cater for plenty of tie-down points
  • Pre-drilled to fit SRC 3 liter plastic fuel tank
  • Easy to drill holes to fit the Roto-Pax fuel/water containers in a position to suit you
  • Quick & easy fitment
    
  
  

Installation instructions and video

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.

However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSE OUT!

Fits- KTM 790/890 ADV 2020-23'

• Made out of 3 mm (1/8") thick Aluminum material and Laser cut to precision
• Cargo Bags can be easily tied-up through the Slots provided on the Front and Back side. 
• Compatible Hardware and Bracketry for easy mounting.
• Gussets are welded with parity to the parent material and Powder coated to prevent corrosion.
• Quick, easy, and DIY fitment 
• Rack Surface is 12" wide at the front, tapering to 9" at the back, and 10" long. 
• Rear rack plate is mounted onto bike using a 3mm stainless steel sub bracket unit that is super strong
• Note: This rear rack does not have any pre drilled mounting holes for Kappa, GIVI or Monokey hard cases.

Available in Satin Black powder coat or clear anodized silver:  Please note, the Silver rack only has the aluminum top cargo rack portion in silver as the tube frame is made of carbon steel and is powder-coated black satin. 

5.25lbs

Fitment: KTM 790/890 ADV 2020-23'

Installation instructions and VIDEO

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged. However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Made of strong 3mm aluminum alloy plate for an optimal balance of strength to weight. Lots of openings for strapping and bungee cords.  22 lb / 10Kg load capacity

The rack is 12" long and 12" at the front and tapers to 11" wide at the rear.

Available in satin black powder coat or clear anodized natural silver to prevent oxidation 

Available for model years:

• Option 1: 2014-2015  - Suzuki V-Strom 650
• Option 2: 2017-2021 - Suzuki V-Strom 650 -&-  2017-2020 - Suzuki V-Strom 1000

NOTE: Accessory quick attachment kit for use with Kappa, GIVI, MONOKEY Hard Cases (and shown in some of the images) is NOT included and no longer available. 

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Clutch Reservoir Cover for Ducati Multistrada

Fits: 2015-2020 Ducati Multistrada 950 / 1200 / 1260

Protect the clutch fluid reservoirs from flying debris and tip-over damage with the SRC aluminum protective reservoir guards. Easily installed in minutes with common hand tools.  Don't risk being stranded with no brakes! 

Constructed of strong yet lightweight 2mm Stainless Steel and processed in state-of-the-art laser cut and CNC bending machines

Available in your choice of satin black powder coat or natural brushed stainless steel finish.  

Product installation info available here

* Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSEOUT SALE!

Fits: KTM 790/890 ADV 2020-22'  ( Orange has sold out) 

Protect your KTM 790/890 Adv's vulnerable underside including the exhaust, oil cooler, side cases, etc with SRC's heavy-duty crash bars & skid plate.

This crash bar is designed to prevent damage from falling, bumps as well

• Full lower crash bars plus skid plate - sold as a set

• Made from 1 ' thick Stainless steel tube 1.8 mm. Cut by modern laser machine and tube bender on CNC machine

• Tube wall thickness 2mm  

• Crash bars also house a 3mm stainless steel plate to protect fuel tank on both sides of the bike

• 4 x Main mounting points on each side of the bike for maximum strength

• Skid plate material - 4mm aircraft grade aluminum plate

• Beautiful and strong connection seams

• Available in powder-coated KTM Orange and electropolished Silver

• The shockproof cover helps to hold the crash bar and reduce impact from falling

• Supplied with all stainless steel brackets & mounting components 

• Easy to assemble, convenient, and fast, there is a manual for installation. And can be downloaded from the SRC website.

Installation instruction video

CLOSEOUT!

Crash Bar Set KAWASAKI VERSYS 1000 - 2019 to 2022

 Black has sold out and is no longer available.

• Available Electropolished  304Stainless Steel silver or Satin Black Powder Coat steel  
• Stout 1" (25mm) tube with 1/8" (3mm ) wall thickness
• CNC Laser cut bracketry and mounts for a precise fit

PRODUCT INSTRUCTIONS LOCATED HERE 

A common question is “Can the skid plate and crash bars be installed together?”  Yes, both parts include spacers that are used in the main mounting locations when the part is installed by itself. When adding the second part, the spacer is removed to allow room for the 2nd parts mounting bracket thickness.

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

• Available electropolished 304 stainless steel silver or satin black powder coat steel  
• Stout 1" (25mm) tube with 1/8" (3mm ) wall thickness
• CNC Laser cut bracketry and mounts for a precise fit

A common question is “Can the skid plate and crash bars be installed together?”  Yes, both parts include spacers that are used in the main mounting locations when the part is installed by itself. When adding the second part, the spacer is removed to allow room for the 2nd parts mounting bracket thickness.

Product instructions available here

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSE OUT

Crash Bar Set SUZUKI V-STROM 1000 2014-2016

• Available electropolished 304 stainless steel silver or satin black powder coat steel  
• Stout 1" (25mm) tube with 1/8" (3mm ) wall thickness
• CNC Laser cut bracketry and mounts for a precise fit
• Sacrificial heavy-duty delrin guards at critical impact zones that are easily replaced if they are damaged in a tip-over
  

A common question is “Can the skid plate and crash bars be installed together?”  Yes, both parts include spacers that are used in the main mounting locations when the part is installed by itself. When adding the second part, the spacer is removed to allow room for the 2nd parts mounting bracket thickness.

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSEOUT SALE ! 

SRC Designs Engine/Crash Bar Set for Yamaha Ténéré 700 2019 - 2025* 

2020-2021 full and lower kits are compatible with SRC skid plate.

*2022-2025 models, you can not use the SRC V2 skid plate and lower crash bars. 

PLEASE NOTE! The SRC lower crash bars as well as most others are not compatible with the SRC V2 skid plate. That being said, the SRC V2 skid plate wing extensions do a good job of protecting the lower portions of the engine. 

Also, some international markets received the EURO 5 updates on the 2021 models (larger catalytic converter in the headpipe), North America models did not get this until 2022.  If you are unsure of how to order, shoot us an email for assistance. 

Stout 1" (25mm) steel tube with 1/8" (3mm ) wall thickness CNC Laser cut bracketry and mounts for a precise fit

Available Electropolished Stainless Steel (SILVER) or Satin Black Powder Coat steel 

Includes sacrificial heavy-duty Delrin guards at critical impact zones that are easily replaced if they are damaged in a tip-over

Compatible with the stock skid plate and most aftermarket skid plates

Choose between:

• Full set (Upper and lower crash bars)
• Upper crash bars only (Lower crash bar can be added later to complete full set)
• Lower crash bars only (Upper crash bar can be added to complete full set)

Product weights:

• Yamaha Tenere 700 SRC Crash Bars (Lower): 7.6 LBS 
• Yamaha Tenere 700 SRC Crash Bars (Upper): 14.8 LBS

Installation instructions  Full set and video

Installation Upper Set

Installation instructions lower bar set

Replacement guard/crash bar pads can be found here A common question is “Can the skid plate and crash bars be installed together?”  Yes, both parts include spacers that are used in the main mounting locations when the part is installed by itself. When adding the second part, the spacer is removed to allow room for the 2nd parts mounting bracket thickness. These crashbars often contain brown colored blasting media particles found in the ends of the bars.  This is not rust and is perfectly normal.Product installation instructions can be found here

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSEOUT!

Exhaust Heat Guard Kawasaki KLX300 R

• Available in both Stainless Steel and Satin Black Powder Coat options.
• Protect the vulnerable header pipe from road debris, rocks and tip over impacts and reduce burns on your leg in tipovers with the SRC Header pipe guard.
• Made of 2mm stainless steel sheet and held securely in place with low profile stainless steel band clamps. 
• Cut-outs across the length of the Guard, ensures light weight and at the same provides Air cooling to subside the Heat/Radiation out of the Header pipe
• Anodized to improve the Corrosion Resistance and Hardness of Surface and Sub-surface
• Easy to install using Steel Band clamps with common hand tools and provides years of protection.

Fitment includes:

2021-2025 Kawasaki KLX 140 / 150 / 230 / 250 / 300R

Installation instructions

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.

However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSEOUT SALE! 

SRC Designs Frame Guard (Left side) for Yamaha Ténéré 700

Fits Yamaha Ténéré 700 years 2020 - 2025

Protect the header downpipe from rocks, road debris, and tip over impacts with this slick stainless steel guard laser cut from stainless steel. 

• Crafted out of 2 mm thick aircraft fuselage grade stainless steel
• Laser-cut, CNC bent on state-of-the-art machines
  
• Easy 5-minute install using the stock fasteners and common hand tools
• Available in natural silver stainless finish or black powder-coated

Product installation information can be found here

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSEOUT SALE!

Pair of Frame Guards HONDA CRF 300L & 300L Rally 2021-2025

Protect the frame side spars from boot scuffs and tip-over damage with the SRC Frame guards. 2mm anodized Aluminum guards.  Easy 10-minute installation adds a rugged Rally look and keeps the frame looking new.  

Available in clear anodized aluminum silver or satin black powder coat. 

*Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSEOUT SALE!

Frame Guards for Kawasaki KLX300R

• Protect the frame side spars from boot scuffs and tip-over damage with the SRC Frame guards.
• 2mm anodized Aluminum guards. 
• Easy 10-minute installation adds a rugged Rally look and keeps the frame looking new.  
• Available in clear anodized aluminum silver or satin black powder coat. 
• Quick and easy install instructions

Fitment:

2021-2025 KLX300R (does not fit the street legal Dual sport model) 

Installation instructions

* Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Fits: 2015-2020 Ducati Multistrada 950 / 1200 / 1260

Protect the front brake caliper from flying debris and tip-over damage with the SRC aluminum protective reservoir guards. Easily installed in minutes with common hand tools.  Don't risk being stranded with no brakes! 

Constructed of strong yet lightweight 2mm Stainless Steel and processed in state of the art laser cut and CNC bending machines. Anodized for improved corrosion resistance

Installed quickly using common handtools.

Available in your choice of satin black powder coat or natural brushed stainless steel finish. 

Price is per pair

* Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Fits: 2015-2020 Ducati Multistrada 950 / 1200 / 1260

Protect the brake fluid reservoirs from flying debris and tip-over damage with the SRC aluminum protective reservoir guards. Easily installed in minutes with common hand tools.  Don't risk being stranded with no brakes! 

Constructed of strong yet lightweight 2mm Stainless Steel and processed in state of the art laser cut and CNC bending machines

Product Instructions available here

* Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

GPS  / Phone Accessory Mounting Bar 2014 - 2015 HONDA NC750

Available in Satin finish stainless steel silver or satin black powder coat.

The SRC DESIGNS GPS bracket bar gives you a solid attachment point on your bike. Gone are the days of trying to read shaky GPS screens. Made of stainless steel and anodized aluminum, this handlebar mounting adapter is built to go the distance.

The GPS mount adapter provides a sturdy 22mm (7/8" inch) diameter mounting bar that is intended for mounting most GPS mounts. It can also be used for roadbook holders or any other device that uses a  common 7/8" clamp.

Fits Honda NC750 2014 - 2015

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

SRC DESIGNS GPS bracket bar for the Kawasaki Versys 1000/ STAINLESS STEEL.

The SRC DESIGNS GPS bracket bar gives you a solid attachment point on your Kawasaki Versys 1000. Gone are the days of trying to read shaky GPS screens. Made of stainless steel and anodized aluminum, this handlebar mounting adapter is built to go the distance.

The GPS mount adapter provides a sturdy 22mm (7/8" inch) diameter mounting bar that is intended for mounting most GPS mounts. It can also be used for roadbook holders or any other device that uses a  common 7/8" clamp.

Choose between versions that fit:

• 2015 to 2018 - PRODUCT INSTRUCTIONS AVAILABLE HERE

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSEOUT SALE! 

SRC DESIGNS GPS bracket bar for the ROYAL ENFIELD HIMALAYAN

2016-2021 or 2022+-2023 models available in black and silver 

2022-2023 part is compatible with Tripper Gauge 

The SRC DESIGNS GPS bracket bar gives you a solid attachment point on your Royal Enfield Himalayan windscreen mount. Gone are the days of trying to read shaky GPS screens. Made of stainless steel and anodized aluminum, this GPS bar is built to go the distance.

The GPS mount adapter provides a sturdy 22mm (7/8" inch) diameter mounting bar that is intended for mounting most GPS mounts. It can also be used for roadbook holders or any other device that uses a  common 7/8" clamp.

Product instructions available here

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSEOUT SALE!

SRC DESIGNS GPS bracket bar for the Kawasaki Versys 1000/ STAINLESS STEEL.

The SRC DESIGNS GPS bracket bar gives you a solid attachment point on your Kawasaki Versys 1000. Gone are the days of trying to read shaky GPS screens. Made of stainless steel and anodized aluminum, this handlebar mounting adapter is built to go the distance.

The GPS mount adapter provides a sturdy 22mm (7/8" inch) diameter mounting bar that is intended for mounting most GPS mounts. It can also be used for roadbook holders or any other device that uses a  common 7/8" clamp.

Choose between versions that fit:

• 2019 to 2023 - PRODUCT INSTRUCTIONS AVAILABLE HERE

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSE OUT

Head Light Guard SUZUKI V-STROM 1000 for 2017-2019

• Pin Mounting allows for quick tool-less removal for cleaning of the headlight lens 
• Developed for on or off-road use
• Includes all necessary mounting hardware and is easily installed with common hand tools

Available in brushed stainless steel finish or satin black powder coat steel 

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Available in Brushed Stainless Steel finish or Satin Black Powder coat steel 

• Pin Mounting allows for quick tool-less removal for cleaning of the headlight lens 
• Developed for on or off-road use

Includes all necessary mounting hardware and is easily installed with common hand tools. 

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Fits Kawasaki Versys 650

This is the dual lock version of our SRC headlight guard.  For the pin and grommet version check out this link.

• Constructed of 2mm stainless steel sheet
• Available in natural stainless silver or satin black powder coat 
• Powerful 3M Dual Lock adhesive mounting system for quick and easy install and removal for clean up. 

* Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSEOUT SALE!

HEADLIGHT GUARD fits 2016-2018 HONDA CB500X
- Constructed of 2mm stainless steel sheet and available in natural stainless silver or Satin Black Powder Coat 
- Developed for on and off-road use

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Available in Brushed Stainless Steel finish or Satin Black Powder coat steel 
- Pin Mounting allows for quick tool-less removal for cleaning of the headlight lens 
- Developed for on or off-road use

Fits BMW G 310 R 2017-2021

* Note: SRC MOTO is located in Oregon which is one US state that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Fits models: 

• 2013-2018 BMW R 1200
• 2019-2020 BMW 1250 GS

Choose between Natural Stainless Silver or Satin Black Powder Coat

• Constructed of 2mm stainless steel sheet
• Pin & Grommet Style Mounting allows for quick tool-free  removal for cleaning
• Developed for on and off-road use

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

HEADLIGHT GUARD FOR HONDA AFRICA TWIN & ADVENTURE SPORT

Choose your bike model:

CLOSEOUT SALE! 

• AFRICA TWIN 2016 - 2020
• AFRICA TWIN ADVENTURE SPORT  2018 - 2020

Choose your color: Available in natural stainless silver or Satin Black Powder Coat

• Constructed of 2mm stainless steel sheet
• Pin & Grommet Style Mounting allows for quick tool-free  removal for cleaning
• Developed for on and off-road use

Product instructions:

• Link to product instructions for HONDA CRF 1000L here
• Link to product instructions for HONDA Africa Twin Adventure sport  here

* Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSEOUT SALE! 

Fits Kawasaki Versys 1000

• Constructed of 2mm stainless steel sheet
• Available in natural stainless silver or satin black powder coat 
• Powerful 3M Dual Lock adhesive mounting system for quick and easy install and removal for clean up. 

Choose between versions that fit:

• 2015 to 2018
• 2019 to 2021

* Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

HEADLIGHT GUARD FOR KAWASAKI VERSYS 650 2015-2021

• Constructed of 2mm stainless steel sheet
• Available in Natural Stainless Silver or Satin Black Powder Coat 
• Pin & Grommet Style Mounting allows for quick tool-free removal for cleaning

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSE OUT!

KICKSTAND SENSOR GUARD FOR BMW G 310 GS 2017-2022

Protect the vulnerable kickstand position sensor from debris and fall impacts that could leave you stranded as the sensor must be functioning for the bike to start. 

Brushed Stainless Steel 

Easily installed in a few minutes with common hand tools and included instructions 

Link to product instructions here

* Note: SRC MOTO is located in Oregon which is one US state that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

NOTE: This is a special order product, lead times are generally 4 to 6 weeks.  You can order now and we will follow up with a more precise eta by email. 

KICKSTAND SENSOR GUARD FOR:

• 2013-2018 BMW R 1200 GS 
• 2019-2022 BMW R 1250 GS 

Protect the vulnerable kickstand position sensor from debris and fall impacts that could leave you stranded as the sensor must be functioning for the bike to start. 

Available in:

• Brushed stainless steel
• Satin black powder-coat

Easily installed in a few minutes with common hand tools 

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.