CLOSEOUT SALE ! 

SRC Designs Engine/Crash Bar Set for Yamaha Ténéré 700 2019 - 2025* 

2020-2021 full and lower kits are compatible with SRC skid plate.

*2022-2023 models, you can not use the SRC V2 skid plate and lower crash bars. 

PLEASE NOTE! The SRC lower crash bars as well as most others are not compatible with the SRC V2 skid plate. That being said, the SRC V2 skid plate wing extensions do a good job of protecting the lower portions of the engine. 

Also, some international markets received the EURO 5 updates on the 2021 models (larger catalytic converter in the headpipe), North America models did not get this until 2022.  If you are unsure of how to order, shoot us an email for assistance. 

Stout 1" (25mm) steel tube with 1/8" (3mm ) wall thickness CNC Laser cut bracketry and mounts for a precise fit

Available Electropolished Stainless Steel (SILVER) or Satin Black Powder Coat steel 

Includes sacrificial heavy-duty Delrin guards at critical impact zones that are easily replaced if they are damaged in a tip-over

Compatible with the stock skid plate and most aftermarket skid plates

Choose between:

• Full set (Upper and lower crash bars)
• Upper crash bars only (Lower crash bar can be added later to complete full set)
• Lower crash bars only (Upper crash bar can be added to complete full set)

Product weights:

• Yamaha Tenere 700 SRC Crash Bars (Lower): 7.6 LBS 
• Yamaha Tenere 700 SRC Crash Bars (Upper): 14.8 LBS

Installation instructions  Full set and video

Installation Upper Set

Installation instructions lower bar set

Replacement guard/crash bar pads can be found here A common question is “Can the skid plate and crash bars be installed together?”  Yes, both parts include spacers that are used in the main mounting locations when the part is installed by itself. When adding the second part, the spacer is removed to allow room for the 2nd parts mounting bracket thickness. These crashbars often contain brown colored blasting media particles found in the ends of the bars.  This is not rust and is perfectly normal.Product installation instructions can be found here

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSEOUT SALE

SRC Designs Rear Brake Master Cylinder Guard for Yamaha Ténéré 700

Fits Yamaha Ténéré 700 years 2020 - 2025

Protect the vulnerable rear master cylinder from a catastrophic failure from a tip-over or impact by flying debris that could leave you without brakes!  

• Constructed of 2mm thick 304 stainless steel for maximum protection! 
• Easily installed in just a couple of minutes to provide a lifetime of protection. 
• Available in brushed stainless steel or satin black powder coat finish. 

Product installation instructions available here

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

HEX DESIGN is on CLOSEOUT

SRC Designs Head Light Guard for Yamaha Ténéré 700

Fits Yamaha Ténéré 700 years 2020 - 2021

Available in Brushed Stainless Steel finish or Satin Black Powder coat steel 

• Pin Mounting allows for quick tool-less removal for cleaning of the headlight lens 
• Developed for on or off-road use

Includes all necessary mounting hardware and is easily installed with common hand tools. 

Installation instructions and video

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Installation PDF 

SRC Designs Full Rack System for the Yamaha Ténéré 700 Version 1 (V1)

Fits Yamaha Ténéré 700 years 2020 - 2024

Not compatible with the optional Rally seat

This is the adventure rack system you want! Innovative modular design made of high strength lightweight aluminum alloy.

The SRC Designs Full Rack System includes left and right pannier racks, center tail rack, mounting hardware, and instructions (easily installed in about 30 minutes with common hand tools)

The Full Rack System features: 

• High-quality stainless steel mounting hardware, mounts using the existing steel subframe rack points (no drilling required)
• Rear Cross Brace for increased rigidity in event of the inevitable tip over.
• Side racks and top rack feature strategically positioned strap slots for quick and secure attachment of most brands of soft luggage.
• Center Tail Rack is nicely sized and shaped to fit the rear of the Yamaha and provides a nice solid foundation for luggage, camping gear, etc. The aluminum rack (weighs just over a pound) mounts to the stock steel subframe points (where the stock strap bolts are located).  The side wings support the load of soft side luggage and keeps the luggage from compressing the side plates 

Powder-coated satin black for a long-lasting durable finish that looks great on the Yamaha Ténéré 700!

Thecenter  top rack is good for small luggage set up and especially Kriega luggage, however if you need access to the battery or electrics whilst on a ride you need to remove the rack which can be a little annoying and secondly the rack fits over the passenger seat so no place for a passenger to sit. The top rack with side racks (the part you are currently viewing) is good for riders that have soft luggage and side racks are slightly raised off the side with rubber stands-offs so they stop potential damage caused by luggage rubbing on the plastics. The new rear rack V2 with grab rails  (available here) is great as it allows access to air filter & electrics etc. without the need to remove the seat whilst out on a ride. The real benefit of V2 is using the grab rails to pick up the bike or lift the bike out of ruts & muddy holes etc...as T7 has nothing to hold onto at the rear of the bike. This V2 option allows for much larger luggage to be carried as racks sits further out off the back of the bike. On a side note, the V2 version can also act as rear crash bars as they stick slightly out from the side of bike. We've tested all options and this also comes from reliable customer feedback.

 Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged

However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSEOUT SALE!

SRC Designs Side stand/Kickstand foot enlarger for Yamaha Ténéré 700

Fits Yamaha Ténéré 700 years 2020 - 2025

Keeps your side stand from sinking into soft ground & hot pavement! 

• Don't find out the hard way why these are so popular! 
• Don't come back to your parked bike to find it on its side after parking on hot pavement or loose soil!

The SRC large side stand base extension (doubles the surface area) installs easily and improves your parking experience when off pavement with your bike.

• Made of laser-cut stainless steel sheet 304 grade 3 mm thickness
• Stainless bolts and locknuts
• Easy installation

Product installation instructions can be found here

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSEOUT SALE! 

SRC Designs Frame Guard (Left side) for Yamaha Ténéré 700

Fits Yamaha Ténéré 700 years 2020 - 2025

Protect the header downpipe from rocks, road debris, and tip over impacts with this slick stainless steel guard laser cut from stainless steel. 

• Crafted out of 2 mm thick aircraft fuselage grade stainless steel
• Laser-cut, CNC bent on state-of-the-art machines
  
• Easy 5-minute install using the stock fasteners and common hand tools
• Available in natural silver stainless finish or black powder-coated

Product installation information can be found here

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

 SRC Designs Cargo Tail Rack for Yamaha Ténéré 700

CLOSEOUT SALE! 

The top plate is made of strong 3mm aluminum alloy plate for an optimal balance of strength to weight. Lots of openings for strapping and bungee cords.  This rack also includes stainless steel support brackets and is rated for up to 22 lbs  (10 Kg) of gear. 

Comparing this V2 HD tube frame rack with our V1 center rack, the center top rack of the V1 is good for small luggage set up and especially Kriega luggage, however, if you need access to the battery or electrics whilst on a ride you need to remove the rack which can be a little annoying and secondly the V1 rack fits over the passenger seat so no place for a passenger to sit. The full version of the V1  top rack with side racks is good for riders that have soft luggage as the side racks are slightly raised off the side with rubber stands offs so they stop potential damage caused by luggage rubbing on the plastics.

This new rear rack (V2) with grab rails is great as it allows access to the air filter & electrics etc. without need to remove the seat whilst out on a ride. The real benefit of V2 is using the grab rails to pick up the bike or lift the bike out of ruts & muddy holes etc...as T7 has nothing to hold onto at rear of bike. This V2 option allows for much larger luggage to be carried as racks sits further out off the back of bike. On a side note, the V2 version can also act as rear crash bars as they stick slightly out from the side of bike. We've tested all options and this also comes from reliable customer feedback.

Pre-drilled for our 3L fuel can mount

Available in Satin Black powder coat

Fitment:

• Yamaha Ténéré 700 years 2020 - 2024*
• • Black powder-coated 3.25mm aluminium top plate
    
  • 25mm (1") Chro-moly steel tube frame for increased load capacity and weight distribution.  Plus acts as much much-needed grab handle!
  • Fits to 4 x existing mounting points on rear of bike
  • Supplied with 4 x stainless steel standoffs to replace existing OEM units 
  • Includes all stainless steel mounting bolts & counter-sunk washers
  • Flat section of the rack sits  approximately 10mm above the passenger seat (standard OEM seat)
  • Slotted all around to cater for plenty of tie-down points
  • Pre-drilled to fit SRC 3 liter plastic fuel tank
  • Easy to drill holes to fit the Roto-Pax fuel/water containers in a position to suit you
  • Quick & easy fitment
    
  
  

Installation instructions and video

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.

However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSEOUT SALE! 

Fits: 2021-2025 Yamaha TÉNÉRÉ 700.

T700-2 will lower the rear 1 inch 

T700-3 will lower the rear 1.50 inches.

Reinforced for added strength/durability when adding weight.

Built in Boise, IDAHO. Ridden and raced everywhere.

Replaces Yamaha part # BW3-2217M-00-00

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged. However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSEOUT SALE! 

SRC Designs Protective Aluminum Skid Plate/Lower Engine Sump Guard for Yamaha Ténéré 700

Fits Yamaha Ténéré 700 years 2019 - 2021*

Does not fit 2022-2023 or models equipped with E5 catalytic converter

Protect your  Tenere's vulnerable underside including the exhaust, oil cooler, side cases, etc with SRC's heavy-duty skid plate.  

• Made of heavy gauge 4mm thick aerospace fuselage aluminum sheet with stainless brackets and hardware. 
• Developed for on and off-road use
• Cutouts allow access to common service points without the need for removal of skid plate

Available in brushed stainless steel or satin black powder-coat

A common question is “Can the skid plate and crash bars be installed together?”  Yes, both parts include spacers that are used in the main mounting locations when the part is installed by itself. When adding the second part, the spacer is removed to allow room for the 2nd parts mounting bracket thickness.

Installation instructions and video 

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSEOUT SALE! 

Installation PDF 

SRC Designs Cargo Tail Rack for Yamaha Ténéré 700 2021-2024 Version 1 (V1) 

Made of strong 3mm aluminum alloy plate for an optimal balance of strength to weight. Lots of openings for strapping and bungee cords.  This rack also includes stainless steel support brackets and is rated for up to 22 lbs  (10 Kg) of gear. 

• Black powder coated aluminium
• Laser cut 3.25mm aluminium plate 
• Light but super strong - only 1.3kg 
• Fits to 4 x existing mounting points on rear of bike
• Supplied with 4 x stainless steel standoffs to replace existing OEM units 
• Includes all stainless steel mounting bolts & counter-sunk washers
• Flat section of the rack sits  approximately 10mm above passenger seat (standard OEM seat)
• Slotted all round to cater for plenty tie down points
• Pre drilled to fit SRC 3 litre plastic fuel tank
• Easy to drill holes to fit the Roto-Pax fuel/water containers in a position to suit you
• Quick & easy fitment
• Please note this rack will not fit with the rally seat 
• Fuel tanks & fuel tank mounting brackets as seen in some of the photos are not included in price (sold as separate parts) 

The top rack is good for small luggage set up and especially Kriega luggage, however if you need access to the battery or electrics whilst on a ride you need to remove the rack which can be a little annoying and secondly the rack fits over the passenger seat so no place for a passenger to sit. The top rack with side racks is good for riders that have soft luggage and side racks are slightly raised off the side with rubber stands-offs so they stop potential damage caused by luggage rubbing on the plastics. The new rear rack V2 with grab rails  (available here) is great as it allows access to air filter & electrics etc. without the need to remove the seat whilst out on a ride. The real benefit of V2 is using the grab rails to pick up the bike or lift the bike out of ruts & muddy holes etc...as T7 has nothing to hold onto at the rear of the bike. This V2 option allows for much larger luggage to be carried as racks sits further out off the back of the bike. On a side note, the V2 version can also act as rear crash bars as they stick slightly out from the side of bike. We've tested all options and this also comes from reliable customer feedback.

Fitment:

• Yamaha Ténéré 700 years 2020 - 2023*

• *Not compatible with optional rally seat

Installation instructions and video*

Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSEOUT SALE!

SRC Designs Protective Aluminum Skid Plate/Lower Engine Sump Guard for Yamaha Ténéré 700 added cutouts for more airflow. Standard protection version. We also offer an upgraded V2 version with left and right wing extensions that provide added protection for the waterpump and hoses on the right side and the ignition cover on the left side.  It's available here on the website. 

Fits Yamaha Ténéré 700 years 2022-2024 (and all Euro 5 exhaust models)

This skid plate is compatible with SRC lower crash bars. 

Protect your  T7's vulnerable underside including the exhaust, oil cooler, side cases, etc with SRC's heavy-duty skid plate.  

• Made of heavy gauge 4mm thick aerospace fuselage aluminum sheet with stainless brackets and hardware. 
• Developed for on and off-road use
• Cutouts allow access to common service points without the need for removal of skid plate

Available in brushed aluminum steel or satin black powder-coat aluminum

A common question is “Can the skid plate and crash bars be installed together?”  Yes, both parts include spacers that are used in the main mounting locations when the part is installed by itself. When adding the second part, the spacer is removed to allow room for the 2nd parts mounting bracket thickness.

Installation instructions and video 

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSEOUT SALE! 

SRC Designs Protective Aluminum Skid Plate/Lower Engine Sump Guard for Yamaha Ténéré 700 added cutouts for more airflow and this V2 version offers left and right wing extensions compared to our standard model. The wings are visible in the photos and provide extra protection for the left side ignition cover and the right side water pipe and hoses. 

PLEASE NOTE! This skid plate is not compatible with most lower crash bars, including SRC lower crash bars. That being said, the wing extensions do a good job of protecting the lower portions of the engine though. 

Fits Yamaha Ténéré 700 years 2022-2025  and all Euro 5 exhaust models

Protect your  T7's vulnerable underside including the exhaust, oil cooler, side cases, etc with SRC's heavy-duty skid plate.  

• Made of 4mm thick aerospace fuselage aluminum sheet with stainless brackets and hardware. 
• Developed for on and off-road use
• Cutouts allow access to common service points without the need for the removal of skid plate

Available in natural brushed aluminum or Satin black powder coat made of a burly 4mm thick aluminum alloy. 

A common question is “Can the skid plate and crash bars be installed together?”  Yes, both parts include spacers that are used in the main mounting locations when the part is installed by itself. When adding the second part, the spacer is removed to allow room for the 2nd parts mounting bracket thickness.

Installation instructions and video 

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.