Honda

PLEASE DOUBLE CHECK YOUR SELECTION BEFORE CHECKING OUT!

Fits 2017 to 2025 Honda CRF 250L Rally/300L Rally models

HONDA was nice enough to include a handy 10 AMP* switched accessory lead that is clipped inside the left front fairing on the CRF 250L Rally & 300L Rally models, however, they have yet to release an accessory lead to plug into it! So we picked up the ball and sourced the correct original HONDA waterproof connectors and built them. All leads are 18" long and allow for safe routing from the left upper fairing, following the factory harness routing to the Rally tower and the mount easily installs using a rubber well nut. 

Two options are available to choose from: 12-volt & Dual USB

Please select between these two versions of the Electrical Accessory Lead:

• Dual USB option
• 12-Volt Socket option

Dual USB Version: This is a high-quality dual USB charger with an OE appearance featuring a water-resistant spring-loaded hinged cover. The dual USB charger outputs 2.1 amps for fast phone charging and features a blue led indicator to let you know it's on. Easily installed in just a couple of minutes, all you need is an 8mm wrench or socket to tighten the well nut to secure the bracket to the Rally Tower tube. (remove the rubber plug from the left end of the upper tower bar and insert well nut and snug it up until the bracket is secure!) And plug the other end into the auxiliary power connector inside the left fairing of the Rally. 

12 Volt Socket Version: (cigarette lighter style) This is a high-quality 12-volt socket we developed to offer an OEM appearance, with a water-resistant hinged spring-loaded cover. Easily installed in just a couple of minutes, all you need is an 8mm wrench or socket to tighten the well nut to secure the bracket to the Rally Tower tube. (remove the rubber plug from the left end of the upper tower bar and insert well nut and snug it up until the bracket is secure!) And plug the other end into the auxiliary power connector inside the left fairing of the Rally. (2017-2019 CRF 250L kit mounts on the front side of the top right fork triple clamp)

Also available on our site: USB Adapter- For your convenience, We've sourced a rugged Dual USB charger with aluminum housing for use with the 12 Volt socket kit-  in the electrical Accessory section of our website.    

* This is a 10 AMP Switched circuit (fuse #5 on the Rally), which means it is turned off and on by the bikes ignition switch.

Here's a shortlist of the average current draw for popular accessories:

• Heated Grips 3-5 AMPS
• USB Phone Charger 1-2 AMPS
• Heated Gloves 3 AMPS
• Heated Jacket 8 AMPS
• Heated Pants 6 AMPS

WARNING: Most High output horns will draw too much amperage for this circuit. If you are planning to use a 12-volt compact air compressor, be sure to check it to make sure it does not draw more than 10 amps! Usually better to get a compressor that connects to your battery tender SAE connector and ensure it's got the proper capacity.

Quick Rally install overview for those of you that may not be familiar with well nuts. 

* Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality. 

Our kit includes  DoubleTakes full adapter kit to allow fitment to all adventure bikes. 

• This kit fits almost any motorcycle make and model - Each pair comes with a Universal Adapter Kit which includes two 10 x 1.25mm Extensions, two 10 x 1.5mm BMW adapters, and one Reverse-Thread Adapter. 

• Here is a quick list:
• HONDA: 250L, Rally, CB500X, NC750, Africa Twins
• KAWASAK: 300X Versys, Versys 650, Versys 1000
• KTM: All adventure models
• SUZUKI: V-Strom 650, V-Strom 1000
• TRIUMPH: Tigers
• Royal Enfield: Himalayan
  
• DUCATI: Multistrada
• BETA: 500RR-S
• BMW: 310 GS, 310 R, 800 GS, 1200 GS, 1200 GS
• YAMAHA: FJ-09, Tenere 700
• And many more!

Over the years we have tried many popular Adventure bike mirror options and always come back to the simple and durable DoubleTake ADV sets as they simply work and provide an excellent field of view with minimal vibration distortion.  We feel this is the most important feature, functionality over form. There are a bunch of small/minimalist options to choose from on the web if you're into that, but safety and visibility are most important to us and that's why we run the DOUBLETAKE ADVENTURE mirrors on all of our bikes. 

Kit includes:  2 mirrors, 2 - 6" RAM Arms, 2 - 1" RAM Ball mounts, and thread adapters for your bike if needed, a small tube of Loctite thread locker (SRC exclusive!) Apply thread locker to adapter and ball mount threads to prevent your mirrors from vibrating loose.  Everything you need to install them in just a few minutes on most bikes!  

Install Tip: We recommend using one of the extension arms tightly clamped onto the ball mount to tighten the ball mount (and adapters if needed) into the mirror mounts of your bike.  

PS- If you are price shopping, please note that we include the correct adapters and spacers for the specific models below as well as Loctite thread locker to keep them from vibrating loose! 

Below is the DoubleTake Mirror inventors story of how the DoubleTakes came to be-

This mirror is the product of much frustration- I spent years breaking other designs and wondering what was going on behind me on the road. Eventually, when I dropped my bike and found myself buying two(!) new master cylinders as a result, I decided it was time to make a really good mirror, one that would function well as a mirror, and also protect the bike (and me) from damage. I had three goals for my design: That it work as well as an OEM mirror for seeing what was going on behind. That it would be indestructible. It would have to give way in a crash to avoid damage not only to the mirror, but also to the bike. That it could fold completely out of the way, so that when I am offroad, I don't have to think about it. Many experiments later, the mirrors for sale here is the result. Both models hit all three marks right on the nose. We use SAE spec glass to give maximum visibility (it can be important to distinguish Crown Victoria headlights from other vehicles!), it is made right here in Colorado Springs from a super tough nylon that we are so certain will survive we offer a lifetime warranty (on the housing, not the glass, but you can buy the glass separately), and sure enough, it folds right down when you want it gone. If you're deciding between the Adventure model, and the Enduro, our advice is simple. If you plan to fold the mirror down a large percentage of the time, the Enduro is right for you. The long size means the head of the mirror tucks away right behind the headlight. If the mirror will more or less remain extended, get the Adventure- the more compact design is more stable at highway speeds. Either way, you can't go wrong.

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

# double take

Inspired by the CRF 250l Rally's bigger brother, the mighty Africa Twin.......

4" X 1.5", the perfect size for placement on the front fender, fairing, helmet, toolbox, just about anywhere!

SOLD AS A PAIR

Made specifically for 2021-2024  Honda CRF 300L & Rally

• Keeps your side stand from sinking into soft ground & hot pavement! 
• Don't find out the hard way why these are so popular! 
• Don't come back to your parked bike to find it on its side after parking on hot pavement or loose soil!

Also available in a 1/2" taller version for bikes running taller suspension settings that can often cause the bike to lean over too far on the stand. 

This side stand extension offers a large contact surface (50% larger than stock) to improve the motorcycle’s parking footprint on rough surfaces and soft ground.  

• Easily installed in just a few minutes with common hand tools. 
• Made in high-quality Stainless Steel for long life
• Laser-cut stainless steel with Inox hardware

Install instructions and video

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

 OVERSTOCK SALE on the Black Version!

For some reason, the CRF 250L and 250L Rally's have really tall seat heights (over 35" and taller than the AFRICA TWIN!?! ), especially for a small displacement beginners bike.

Fits 2013-2020 250L & Rally

So we have some options to get your feet firmly on the ground. We are pleased to offer these custom-shaped lowering seats that lower the seat height by 2". These are brand new original HONDA seats that have been hand shaped and re-formed to reduce the seat height by 2" There is still 1-1/2" of foam cushion in the main seating area, so normal ADV riding won't be an issue, but if you are a hard-charging off-roader frequently getting airborne, it might be a bit firm on some landings! :-) 

These were developed after my wife was about to give up on her Rally as it was too tall for her. She is relatively new to offroad riding and really felt unsafe and uncomfortable on the Rally, especially when riding on sidehills and slippery surfaces where she was not able to touch the ground when needed. We had already installed a lowering link and that helped, but she wanted it lower to feel comfortable. So we gave one of these a try and she now loves her Rally!  Easily installed in just a couple of minutes with common hand tools. 

Now available in your choice of RED or BLACK- Please make a selection

We occasionally get further inquiries regarding lowering options and this is our general reply: 

The cons of running a link are due to the geometry change in the suspension. In a nutshell, the bike becomes "choppered out" slightly. So the bike likes to go straight (improves straight-line stability), but when cornering on loose surfaces such as gravel roads or lose dirt, the bikes front end will have a bit more of a tendency to plow or push through corners. This is not noticeable on pavement and a beginner off road rider probably won't push the limits of traction enough to have it be an issue, but if you are an experienced off-road rider, you will most likely notice it.  

* These are brand new original HONDA seats that have been hand shaped and re-formed to reduce the seat height by 2" 

* Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality. 

Rear Brake Master Cylinder Guard HONDA CRF 300L & Rally 

Fits: 2021 Honda CRF 300L

Protect the vulnerable rear master cylinder from a catastrophic failure from a tip-over or impact by flying debris that could leave you without brakes!  

• Constructed of 2mm thick 304 stainless steel for maximum protection! 
• Easily installed in just a couple of minutes to provide a lifetime of protection. 
• Easy install with common hand tools.  

Available in natural stainless finish or satin black powder coat. 

Installation instructions and video

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

PLEASE DOUBLE CHECK YOUR SELECTION BEFORE CHECKING OUT!

HONDA was nice enough to include a handy 10 AMP* switched accessory lead connector that is hidden inside a small black vinyl protective boot located behind the headlamp on the right side on 2017-2025 HONDA CRF 250L/300L models.  However, HONDA has yet to release an accessory lead to plug into it! So we picked up the ball and sourced the correct original HONDA waterproof connectors and built it.

DUAL USB Version: This is a high-quality dual USB charger with an OE appearance featuring a water-resistant spring-loaded hinged cover. The dual USB charger outputs 2.1 amps for fast phone charging and features a blue led indicator to let you know it's on. Easily installed in just a couple of minutes, all you need is a 10 mm wrench or socket to secure the mount bracket to the upper right triple clamp bolt.  And plug the other end into the auxiliary power connector mentioned above. Step by step instructions with photos are included. 

12 Volt Socket Version: (cigarette lighter style) This is a high-quality 12-volt socket we developed to offer an OEM appearance, with water-resistant hinged spring-loaded cover. Easily installed in just a couple of minutes, all you need is a 10 mm wrench or socket to secure the mount bracket to the upper right triple clamp bolt.  And plug the other end into the auxiliary power connector mentioned above. Step by step instructions with photos are included. We offer a nice rugged aluminum housing USB adapter here in the electrical section if needed. 

* This is a 10 AMP Switched circuit (fuse #5 on the Rally), which means it is turned off and on by the bikes ignition switch.

Here's a short list of the average current draw for popular accessories:

Heated Grips 3-5 AMPS

USB Phone Charger 1-2 AMPS

Heated Gloves 3 AMPS

Heated Jacket 8 AMPS

Heated Pants 6 AMPS

WARNING: Most High output horns will draw too much amperage for this circuit. If you are planning to use a 12-volt compact air compressor, be sure to check it to make sure it does not draw more than 10 amps! Usually better to get a compressor that connects to your battery tender SAE connector and ensure it's got the proper capacity.

Here's the connector as viewed from the right side of the bike, just behind the headlight looking upwards from the side reflector area. 

* Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

HONDA was nice enough to include a handy 10 AMP* switched accessory lead that is clipped inside the left front fairing on the 2017-2020 CRF 250L Rally models. The 2017-20225 CRF 250L/300L and Rally's accessory connector is located behind the headlamp on the right side.  It is located inside a small black vinyl protective boot.  However, HONDA has yet to release an accessory lead to plug into it! So we picked up the ball and sourced the correct original HONDA waterproof connectors and built it. Leads are 18" long and allow for safe routing, following the factory harness routing to the instrument cluster area or handlebars to connect to your accessory.  

Our plug-and-play accessory lead is easy to install,  just unclip the stock connector cap, connect this lead and attach to your accessory with the included posi lock quick connectors! Posi Lock instructions are included in each kit.  

Kit includes 18" 2 circuit lead (18 gauge red 12V+ and Black ground) terminated with Posi Lock connectors with abrasion sheath and 2 black zip ties for secure installation.  Posi-Lock® Connectors have been put to the test worldwide since 1997. Superior in-line splices with just hand tightening! These electrical connectors require no crimping or soldering.  An electrical connector that meets the needs of today's OEM's, and is so good, it's reusable. Truly a connector for the 21st century.  

Easily installed in about 10 minutes with common hand tools. No modifications or cutting of any wires required. Detailed instructions with photos are included. 

Details on the Rally connector location below. 

Details on the 2017-2020 HONDA CRF 250L accessory connector location below.  (it's in a vinyl protective boot behind and below the right side of the headlight. 

The view below is from the right side of the bike looking upwards from the ara near the right side reflector.  

 This is a 10 AMP Switched circuit, which means it is turned off and on by the bikes ignition switch.

Here's a shortlist of the average current draw for popular accessories:

• Heated Grips 3-5 AMPS
• USB Phone Charger 1-2 AMPS
• Heated Gloves 3 AMPS
• Heated Jacket 8 AMPS

Heated Pants 6 AMPS

WARNING: Most High output horns will draw too much amperage for this circuit. If you are planning to use a 12-volt compact air compressor, be sure to check it to make sure it does not draw more than 10 amps! Usually better to get a compressor that connects to your battery tender SAE connector and ensure it's got the proper capacity.

 * Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Protect your 300L's vulnerable underside including the exhaust, oil cooler, side cases, etc with SRC's heavy-duty skid plate. 

• Made of 5mm thick aerospace-grade aluminum sheet with stainless hardware 
• Gussets are welded with parity to the parent material and anodized to provide strength and protection from corrosion
• Developed for on and off-road use
• Cutouts allow access to common service points without the need for removal of skid plate

Available in both Silver Aluminum and Satin Black Powder Coat options

Installation instructions

The 300L Rally skid plate/Crashbar combo is available here. 

The 300L skidplate can be installed on the Rally models by removing / trimming the bodywork plastics. 

Here's a link to a video of the process by a friend of ours. 

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Fits 2021-2024 300L RALLY

About 2" lower than stock seat

For some reason, the CRF 300L and Rally's have really tall seat heights (over 35" and taller than the AFRICA TWIN!?! ), especially for a small displacement beginner bike.

So we have some options to get your feet firmly on the ground. We are pleased to offer these custom-shaped lowering seats that lower the seat height by about 2". These are brand new original HONDA seats that have been hand-shaped and re-formed to reduce the seat height by about 2" There is still 1-1/2" of foam cushion in the main seating area, so normal ADV riding won't be an issue, but if you are a hard-charging off-roader frequently getting airborne, it might be a bit firm on some landings! :-) 

These were developed after my wife was about to give up on her Rally as it was too tall for her. She is relatively new to offroad riding and really felt unsafe and uncomfortable on the Rally, especially when riding on sidehills and slippery surfaces where she was not able to touch the ground when needed. We had already installed a lowering link and that helped, but she wanted it lower to feel comfortable. So we gave one of these a try and she now loves her Rally!  Easily installed in just a couple of minutes with common hand tools. 

We occasionally get further inquiries regarding lowering options and this is our general reply: 

The cons of running a link are due to the geometry change in the suspension. In a nutshell, the bike becomes "choppered out" slightly. So the bike likes to go straight (improves straight-line stability), but when cornering on loose surfaces such as gravel roads or lose dirt, the bikes front end will have a bit more of a tendency to plow or push through corners. This is not noticeable on pavement and a beginner off road rider probably won't push the limits of traction enough to have it be an issue, but if you are an experienced off-road rider, you will most likely notice it.  

* These are brand new original HONDA seats that have been hand-shaped and re-formed to reduce the seat height by 2" 

 * Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.

However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality. 

SRC Designs Radiator Guard kit fits HONDA CRF 300L (& RALLY) 2021-2024 models

Laser-cut 2 mm thick Stainless steel and symmetrical honey-comb design provides a proper defense against rocks, limbs and other debris you might encounter on your adventures!  

All mounting hardware is included and the guard is easily installed in about 10 minutes with common hand tools. 

Available in powder coat black or natural silver

Product instructions located HERE

Installation video:  For 300L Below

Installation Video for 300L Rally Below 

•  Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
  

However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

OVERSTOCK SALE!

For some reason, the CRF 250L and Rally's have really tall seat heights (over 35" and taller than the AFRICA TWIN!?! ), especially for a small displacement beginners bike. So we have some options to get your feet firmly back on the ground.

Built in Boise, IDAHO. Ridden and raced everywhere.

We are pleased to offer lowering links by KOUBA LINK:

• 250L L 1.75" Lowering Link: For the standard 2013-2020 CRF 250L, This KOUBA LINK lowers the bike 1-3/4" (44.5mm)

• RALLY 1.5" Lowering Link: This KOUBA LINK lowers the 2017-2020 CRF 250L Rally 1-5" (38mm) in the rear.

 * Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.

However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

SRC Designs Aluminum Center Rear Cargo Rack - CRF HONDA 300L & 300L Rally 2021-2025

Top Rack Dimensions: 14" long, 10" wide at the front and tapering towards the rear to 9" wide. 

Nicely sized and shaped to fit the rear of the 2021 300L & Rally and provides a nice solid foundation for luggage, camping gear, etc. The aluminum rack (weighs just over a pound) mounts to the stock steel subframe points (where the stock strap bolts are located). 

Includes high-quality stainless steel mounting hardware, mounts utilize the existing steel subframe rack points (no drilling required), the installation guide is also included. 

Powder-coated satin black for a long-lasting durable finish that looks great on the 300L & Rally! 

Also available in an economy-minded steel version (3.9 lbs)  Please see this product on our site for more details.

Link to product instructions here 

* Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Buy it now - Use it forever - Lifetime Guaranteed

COMPATIBILITY
Works seamlessly with all cell phones and devices up to 3.4 inches wide and 5/8" thick. This includes all standard and Plus sized iPhones with or without a protective case. Samsung Galaxy, LG, HTC, you name this motorcycle phone mount will hold it.. Securely.
The beauty of this mount is you're able to get any phone, with any phone case, in and out of the cradle with a single hand. Loaded with dual industrial spring creating a rock steady hold on your cell phone while allowing to easily get the phone in and out of the cradle with a single hand.

INSTALLATION 
Installation is a breeze - 2 Minute Installation
The kit comes with 3 custom fittings for 7/8", 1" and 1-1/4" bars (Also, works with 1.31" over-sized road bike or mountain bike Bars.)  And fits all SRC GPS Bars
1. Simply place the appropriate spacer over the bar. Connect the clamp with the included wrench and two screws.
2. Loosen the ball and socket joint and position the phone into the desired position. Lock into place.
3. From here you will be able to easily place and remove your phone from the mount with a single hand.
Ride off into the sunset...

TACKFORM ENDURO Overview

Installation Overview below

Fits: 2012-2025 HONDA CB500X & NX500 

Kit includes a pair of wide peg adapters

If you've never run a wider high-quality footpeg, you will be pleasantly surprised by the improvement this inexpensive and easy to install upgrade will make! Upgrading to a wider platform footpeg makes a dramatic improvement in comfort as well as greatly improving grip in wet muddy conditions. Our peg adaptors are a great value and easy to install.

It only takes about 10 minutes to install with common hand tools. The additional width and aggressive tooth profile offer about more contact surface to reduce foot arch strain and improve grip. The wide platform and increased contact points will improve rider confidence in sketchy situations!

• Made of Stainless Steel
• Developed for off-road use
• 55mm wide and 90mm long

Installation instructions and video

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

HONDA was nice enough to include a handy 10 AMP* switched accessory lead connector that is clipped to a metal bracket just behind the bottom of the left radiator (see photo in product listing), however, they have yet to release an accessory lead to plug into it! So we picked up the ball and sourced the correct original HONDA waterproof connectors and built this 12-volt socket version. Leads are 24" long and allow for safe routing from the lower-left radiator area following the factory harness routing to the left upper triple clamp bolt for a quick and secure mount. 

DUAL USB Version: This is a high-quality dual USB charger with an OE appearance featuring a water-resistant spring-loaded hinged cover. The dual USB charger outputs 2.1 amps per port for fast phone charging and features a blue led indicator to let you know it's on. Easily installed in just a couple of minutes, all you need is a 10mm wrench or socket to install the bracket to the upper triple clamp.  And plug the other end into the auxiliary power connector behind the lower left radiator area following the factory harness routing. 

12 Volt Socket Version: (cigarette lighter style) This is a high-quality 12-volt socket we developed to offer an OEM appearance, with a water-resistant hinged spring-loaded cover. Easily installed in just a couple of minutes, all you need is a 10mm wrench or socket to install the bracket to the upper triple clamp.  And plug the other end into the auxiliary power connector behind the lower left radiator area following the factory harness routing. 

All Kits include 18" 2 circuit lead (18 gauge Red 12V+ and Black ground) with abrasion sheath and 2 black zip ties for secure installation.

This is a 10 AMP Switched circuit, which means it is turned off and on by the bikes ignition switch.

Here's a shortlist of the average current draw for popular accessories:

• Heated Grips 3-5 AMPS
• USB Phone Charger 1-2 AMPS
• Heated Gloves 3 AMPS
• Heated Jacket 8 AMPS
• Heated Pants 6 AMPS

WARNING: Most High output horns will draw too much amperage for this circuit. If you are planning to use a 12-volt compact air compressor, be sure to check it to make sure it does not draw more than 10 amps! Usually better to get a compressor that connects to your battery tender SAE connector and ensure it's got the proper capacity.

*Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

The Rally Dual LED headlamp assembly is really cool. It's also $654 to replace......

Protect it from impact damage with the SRC Designs Headlamp guard kit. Laser-cut 14 gauge steel powder coated satin black provides a proper defense against rocks, limbs and other debris you might encounter on your adventures!  

All mounting hardware is included and the guard is easily installed in about 10 minutes with common hand tools. 

Available in powder coated black or stainless steel (silver)

Fits Honda CRF 250L Rally & 300L Rally 2017-2025

Installation video here.

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.

However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

SRC Crash Bars have cool sacrificial nylon pads that are strategically positioned to be the point of impact if you happen to drop your bike or have a tip over.  If you do happen to scratch one up, you can easily remove it and install a freshie!

These are designed to fit 1" diameter bars. All SRC bars are 1" and they should fit other brands of crash bars that are 1"/25mm diameter. 

 Please Note: These are not solid frame sliders.  Frame sliders are designed to grind away in a fall on the pavement at speed. These are more for tip-overs at low speed to protect the crash bars from scratches etc.  

Price is per replacement pad. (order 1 pad, get 1 pad)

For some reason, the CRF 300L and Rally's have really tall seat heights (over 35" and taller than the AFRICA TWIN!?! ), especially for a small displacement beginners bike. So we have some options to get your feet firmly back on the ground.

Built in Boise, IDAHO. Ridden and raced everywhere.

We are pleased to offer lowering links by KOUBA LINK for the Honda CRF 300L and Rally, which lowers the bike 1-3/4" (44.5mm)

Available in Red or Black colors, make your choice below.

Fits both the standard 2021-2024 CRF 300L and the Rally version.

Also lowers the new 300 LS 1.5" 

Please be aware: All lowering link alter the rear shock linkage leverage ratio, effectively making the rear shock spring softer. And it's already too soft for most riders as it's set up for a 100 lb beginner rider.  If you ride primarily on the street, it probably won't be that big of a deal, but if you ride off-road on loose surfaces, it will have a tendency to make the bike plow through corners instead of carving corners. The front end will push if that makes sense. 

* Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

OVERSTOCK SALE on the Tall version! 

Made specific for 2013-2020 Honda CRF 250L & Rally

• Keeps your side stand from sinking into soft ground & hot pavement! 
• Don't find out the hard way why these are so popular! 
• Don't come back to your parked bike to find it on its side after parking on hot pavement or loose soil!

This side stand extension offers a large contact surface (50% larger than stock) to improve the motorcycle’s parking footprint on rough surfaces and soft ground.  

• Easily installed in just a few minutes with common hand tools. 
• Made in high-quality Stainless Steel for long life
• Laser-cut stainless steel with Inox hardware

PRODUCT INSTRUCTIONS AVAILABLE HERE

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Fits: All 2012-2025 CRF250L, Rally 250L , 300L, 300LS & Rally 300L 

(Not available for ABS models)  

PLEASE NOTE: Our front line for the 2012-2024 CRF250L, Rally 250L , 300L & Rally 300L models is 2" shorter than the stock line to reduce clutter and improve the view of the instrument cluster. 

MOTO STUFF premium Steel Braided Brake lines by CORE MOTO are made to our own specifications using only the highest quality materials including Dupont PTFE liners and a tight weave aircraft-grade stainless steel casing covered in Clear, Red or Stealth Black vinyl and an industry exclusive clear translucent HD ACRYLON sheathing to prevent abrasion and provide precise alignment on the bike.

The stainless steel banjo fittings are powder coated bright Red or Blue and are adjustable for precise fitment! Each line also comes with Stainless steel Banjo Bolts and a new set of copper sealing washers.

Upgrading to a stainless line will improve brake lever feel by reducing line expansion, especially on bike with stock rubber lines that are more than 6 months old (around 20-30 hours of use) year old which will begin to flex and balloon when the brakes are applied. Also, the smaller inside diameter of our lines reduces the volume of fluid being compressed so the response is quicker.

Our lines are made using 2.5mm tubing vs the 3mm tubing most common aftermarket braided lines are made of. This improves response. 

The patented adjustable banjo fittings eliminate binding issues and excessive rubbing /abrasion. (easily adjusted using pliers to grip and rotate the line at the crimp joint area) Kit includes 1 line, a set of 4 new crush washers and 2 stainless steel banjo bolts.

* Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Fits all 2012-2025 HONDA CRF 250L/300L and Rally Models* 

If you've never run a wider high-quality footpeg, you will be pleasantly surprised by the improvement this inexpensive and easy-to-install upgrade will make! Upgrading to a wider platform foot peg make s a dramatic improvement in comfort as well as greatly improving grip in wet muddy conditions. Our 50mm wide Chrome-Moly pegs are a great value and easy to install.

Our 50mm wide Chrome-Moly pegs are a great value and an easy to install upgrade. Huge upgrade compared to the narrow 38mm stock pegs.

* Please note: The 300L Rally comes equipped with a larger peg than the other models, so not much of an upgrade on that model. 

It only takes about 10 minutes to install with common hand tools. The 50mm width and aggressive tooth profile offer about 50% more contact surface to reduce foot arch strain and improve grip. The wide platform and increased contact points will improve rider confidence in sketchy situations!

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

The Rally Pro X-Strong is a durable injection-molded Nylon composite handguard that features an anodized aluminum bar for ultimate protection. It includes an indexed steel bar-end insert that mounts solidly and will not allow the guard to rotate in a crash. The included X-Strong mount kit allows the protection to be mounted to the handlebar with plenty of room for cables and brake lines. Optional spoilers are sold separately.

This is a universal part that fits most adventure motorcycles: Please note that some models with adjustable windscreens may need to have the windscreen in the forward-most location, such as the Royal Enfield Himalayan, to avoid contact at full lock. These are not compatible on Honda CB500X's and Honda Africa Twins.

PLEASE NOTE: Some OEM bars will require the removal of weighted bar ends and possibly other minor modifications to install handguards.  

For example- 

Choose from black, white or red colors.

View product instructions here

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged. However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

SRC Full Dash Panel 2017-2020 CRF 250L Rally 

Add some room for switches and electrical accessories in an ergonomically safe and accessible location around the perimeter of the stock instrument panel.  Constructed of 16 gauge steel powder coated a nice satin black.   

* Due to popular demand, we have now upgraded the full dash with the switches fully wired and ready to attach to the 12V+ connection of your 12-volt accessories such as auxiliary lights, heated grips, heated gear, etc. Each switch offers an 18" long wire lead that is controlled by the rocker switch and terminated with a Posi-Lock (see below for a description of how Posi-lock functions). This circuit is powered by the bikes auxiliary 12-volt power source that the dash plugs into, so the switches power will also be turned off when the ignition is switched off.  Please call or email if you need further explanation of how it works, but basically, all the SRC dash accessory circuits are switched by the ignition.  The 2 rocker switches provide additional power and switching options whenever the key is in the on position. 

Includes:

• Dash panel with water-resistant rocker switches with bright red LED indicators
• Our best water-resistant 12-volt socket, and Dual USB Charger
• Wiring harness that plugs into the 12-volt accessory connector* inside the left fairing, making this a plug and play upgrade! 

To install, you'll need to remove the instrument panel. This is fairly easy. It takes about half an hour with common hand tools.  We recommend watching the first 60 seconds of our LED TURN SIGNAL VIDEO as it clearly shows how to remove the windscreen,  the headlight assembly for easy access to the 3 screws that hold the instrument panel in place as well as the wiring harness connector. With the panel removed, position the Rally Dash into place end then simply re-install the panel, headlight, and windscreen, connect the power lead to the 12-volt connector inside the left fairing (you'll need to remove the protective dust cap prior to making the connection) and you are ready to wire up the switches to power your favorite electrical accessories! * 

 If you purchase the non pre-wired switches version- Here's How to wire the included switches to power additional accessories. (PS- Due to popular demand, we now offer a version of the dash with the switches fully wired and ready to attach to your 12-volt accessories such as auxiliary lights, heated grips, heated gear, etc) 

 *This is a 15 AMP switched circuit on the 250L Rally, which means it is turned off and on by the bikes ignition switch.

Here's a shortlist of the average current draw for popular accessories:

• Heated Grips 3-5 AMPS
• USB Phone Charger 1-2 AMPS
• Heated Gloves 3 AMPS
• Heated Jacket 5 AMPS
• Heated Pants 5 AMPS

WARNING: Most High output horns will draw too much amperage for this circuit. If you are planning to use a 12-volt compact air compressor, be sure to check it to make sure it does not draw more than 10 amps! Usually better to get a compressor that connects to your battery tender SAE connector and ensure it's got the proper capacity.

Nice video below that one of our customers put together covering the install and functionality. 

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Overstock Reduction Sale! 

Fits 2013-2025 Honda CB500X & NX500

• Keeps your side stand from sinking into the soft ground & hot pavement! 
• Don't find out the hard way why these are so popular! 
• Don't come back to your parked bike to find it on its side after parking on hot pavement or loose soil!

This side stand extension offers a large contact surface (50% larger than stock) to improve the motorcycle’s parking footprint on rough surfaces and soft ground.  

• Easily installed in just a few minutes with common hand tools. 
• Made in high-quality Stainless Steel for long life
• Laser-cut stainless steel with Inox hardware
• Compatible with OEM and aftermarket center stands
• Serrated face nuts help prevent loss from vibration

Product instructions located here

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Tail Tidy - Shortened Taillight and license plate bracket HONDA CRF 300L & 300L Rally 2021-2024.

NEW Revised version to accommodate US and Global market license plates and license plate lights is shown in the install video above.

Clean up the look of your Honda CRF 300L's back end & license plate holder.

• Made of 3mm stainless steel sheet and held securely in place.
• Easily installed in just a few minutes with common hand tools. 
• Available in Satin Black Powder Coat.

Product instructions are available here * Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged. However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

OVERSTOCK SALE!

SRC Designs Full Rack System with Gas Can for the 2021 -2025 CRF HONDA 300L & Rally 300L* 

This is the Adventure Rack System you want!

Innovative modular design made of high-strength lightweight aluminum alloy. Entire rack only weighs 4.2 lbs! 

Top rack surface dimensions are roughly 14” long and 9’ wide at the front, tapering to 8” at the rear.

Side racks add other 12” X 6” top surface making the full rack top surface roughly 14” X 20”

Side rack dims are approximately 12” X 8”

The SRC Designs Full Rack System includes left and right pannier racks, center tail rack, mounting hardware, and instructions (easily installed in about 30 minutes with common hand tools)

The Full Rack System + Gas Can features: 

• High-quality stainless steel mounting hardware, mounts using the existing steel subframe rack points (no drilling required)
• Pre-Drilled for MOTO STUFF Fuel can quick-release mount. (Not compatible with ROTOPAX)
• Side racks and top rack feature strategically positioned strap slots for quick and secure attachment of most brands of soft luggage.
• Center tail rack is nicely sized and shaped to fit the rear of the bike and provides a nice solid foundation for luggage, camping gear, etc. The aluminum rack (weighs just over a pound) mounts to the stock steel subframe points (where the stock strap bolts are located). 
• Racks are powder-coated satin black for a long-lasting durable finish
• Gas Can is a rugged 3l (.8 gallons) spare fuel container similar in design and function to the popular ROTOPAX cans, but shaped to fit inside the left rear SRC Pannier Rack.  Includes quick-release mount and hardware that easily attaches to the inside of the left SRC pannier rack, which is pre-drilled for this mount. 
• Shown in photos with add-on tool tube which is not included with this kit but can be purchased separately)

Installation instructions and video

NOTE: We recommend using blue thread locker on the fasteners.

 Here's another more detailed video we did that also shows how the gas can is easily removed. 

Please Note: The CRF 300L/Rally specifications indicate a max subframe load of 35 lbs. We have been loading our racks with nearly 60 pounds of gear for the past 2 years and have put about 8,000 miles on our 2 Honda 250L's over all types of terrain and we have not had any issues with the racks or subframe, but the more extreme your usage, it is something to be aware of and take into consideration. 

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Fits 2012-2025 HONDA CB500X & NX500 

Trick lightweight aluminum tail rack in silver brushed aluminum or satin black powder coat with top-quality stainless hardware for your CB500X!  

This rack includes a tubular structural support brace that greatly improves the load capacity compared to other racks that simply attach directly to the subframe.  You can safely carry up to 35 lbs  (16 Kg's) with this rack system. 

Rack is approximately 11"wide at the front and tapers to 8" in the rear and is 11" long. 

No drilling or modifications required, easily mounts in under an hour with common hand tools. 

Installation PDF 

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.

However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Overstock reduction Sale! 

Fits HONDA CB500X 2013-2023

Robust enough to protect the vulnerable and expensive radiator against flying stones and other debris.
- This protector made of stainless steel sheet 304 grade 1.5 mm thickness
- Can be easily mounted in a few minutes with common hand tools 

Installation instructions and video

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

SRC Full Dash Panel 2021-2024 CRF 300L Rally  

Does not fit the 300L due to ignition switch interference. 

 Add some room for switches and electrical accessories in an ergonomically safe and accessible location around the perimeter of the stock instrument panel.  Constructed of 16 gauge steel powder coated a nice satin black.  

PLEASE NOTE! If your Rally is equipped with ABS, you will need to relocate the ABS switch and bracket.  (see video at the bottom of this page for details) 

Please note that the installed image shows a red and green switch.  These are for the Asia market, we upgrade to a higher quality switch as shown in the 1st image.  

Includes:

• Dash panel with water-resistant rocker switches with bright red LED indicators
• Our best water-resistant 12-volt socket, and Dual USB Charger
• Wiring harness that plugs into the 12-volt accessory connector* inside the left fairing, making this a plug and play upgrade! 

To install, you'll need to remove the instrument panel. This is fairly easy. It takes about half an hour with common hand tools.  We recommend watching the first 60 seconds of our LED TURN SIGNAL VIDEO as it clearly shows how to remove the windscreen,  the headlight assembly for easy access to the 3 screws that hold the instrument panel in place as well as the wiring harness connector. With the panel removed, position the Rally Dash into place end then simply re-install the panel, headlight, and windscreen, connect the power lead to the 12-volt connector inside the left fairing (you'll need to remove the protective dust cap prior to making the connection) and you are ready to wire up the switches to power your favorite electrical accessories! * 

* Due to popular demand, we now offer a version of the dash with the switches fully wired and ready to attach to the 12V+ connection of your 12-volt accessories such as auxiliary lights, heated grips, heated gear, etc. Each switch offers an 18" long wire lead that is controlled by the rocker switch and terminated with a Posi-Lock (see below for a description of how Posi-lock functions). This circuit is powered by the bikes auxiliary 12-volt power source that the dash plugs into, so the switches power will also be turned off when the ignition is switched off.  Please call or email if you need further explanation of how it works, but basically, all the SRC dash accessory circuits are switched by the ignition.  The 2 rocker switches provide additional power and switching options whenever the key is in the on position. 

 If you purchase the non pre-wired switches version- Here's How to wire the included switches to power additional accessories. (PS- Due to popular demand, we now offer a version of the dash with the switches fully wired and ready to attach to your 12-volt accessories such as auxiliary lights, heated grips, heated gear, etc) 

 *This is a 15 AMP switched circuit on the 250L Rally, which means it is turned off and on by the bikes ignition switch.

Here's a shortlist of the average current draw for popular accessories:

• Heated Grips 3-5 AMPS
• USB Phone Charger 1-2 AMPS
• Heated Gloves 3 AMPS
• Heated Jacket 5 AMPS
• Heated Pants 5 AMPS

WARNING: Most High output horns will draw too much amperage for this circuit. If you are planning to use a 12-volt compact air compressor, be sure to check it to make sure it does not draw more than 10 amps! Usually better to get a compressor that connects to your battery tender SAE connector and ensure it's got the proper capacity.

Nice video below that one of our customers put together covering the install and functionality on a 250L Rally. 300 L Rally is pretty much the same. 

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Ohlins Rear Shock for Rally HONDA CRF 250L RALLY 2017-2020

The single biggest complaint from CRF 250l and Rally owners is that the suspension is sprung way too light and the damping is inadequate. The bike seems to be set up for a 100-pound beginner rider- Here's how to fix that.  A heavier spring or adjusting the pre-load will not resolve the issue. 

Ohlins STX46 Shock for 2017-2020 HONDA CRF 250L Rally
The shock comes with 2 spring options included. The factory-installed (64Nm/mm-6.53Kg/mm) spring on the shock is for riders up to 175 lbs (80 kg) and the stiffer (7.0Nm - 7.15Kg/mm) is for riders 175 lbs-215 lbs (80-98 kg). We also offer an extra Heavy Ohlins Spring (75 Nm/mm- 7.65Kg/mm) for 225 lb-260 lb riders (102-118 kg) available above for an additional $96  We can install the heavy spring or extra heavy spring for $85 installation fee for you if you like.  Simply add the spring install service to your cart and we will swap the springs (Only available for Rally models), usually the same day you place your order, so there will be no delay in shipping. (If you are installing on an ABS model, please click here to view the ABS install supplement sheet)

 PS- If you are installing the kit yourself, PLEASE NOTE! 

CLOSEOUT SALE!

Pair of Frame Guards HONDA CRF 300L & 300L Rally 2021-2025

Protect the frame side spars from boot scuffs and tip-over damage with the SRC Frame guards. 2mm anodized Aluminum guards.  Easy 10-minute installation adds a rugged Rally look and keeps the frame looking new.  

Available in clear anodized aluminum silver or satin black powder coat. 

*Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

2" / 50mm taller than the original windscreen. 

Fits HONDA CRF 250L Rally & 300L Rally 2017-2025 

Please note, that we had quality problems with these in the past and discontinued them. We were recently contacted (October of 2024) by a new manufacturer and the quality is excellent. They are laser cut and machine formed, so the fit and finish is superior to what we had in the past. 

If you are 5'8" or taller, you have probably noticed that the stock windscreen on the Rally is just a bit short and allows some wind buffeting to occur at cruising speeds. 

Easily installed in just a couple of minutes using 5mm allen wrench.

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.